![]() ![]() After you hear the click sound, push down the front end of the adapter by 45 degrees. Lock the adapter into place by pushing it into the cross pin. Align the adapter’s center channel with the blade’s cross pin. Position the adapter so that the end with the tab goes towards the side of the wiper blade with a small hole. The new adapter will go into the vacant adapter slot. Hold the blade in one hand and push the adapter upward using your other hand. How To Install Rain X Wiper Blades On Large Pin Wiper Arms? Step 1. Gently rest the wiper arm on the windshield afterward. Tug on the blade to confirm that it has been attached the right way. Slide the front end of the bayonet arm into the opening and keep on sliding the blade in until it locks. Push the adapter outward to create an opening to put the blade into the wiper arm. Remove the adapter, install the new one, and then attach the blade to the bayonet wiper arm of your vehicle. I will not explain the first two steps in this case because they are the same as they were for the J hook installation. How To Install Rain X Wiper Blades On Bayonet Wiper Arms? Remove the plastic covers from the blade and gently put the windshield wiper back down. ![]() Pull the blade to verify that it has actually fastened. After you reach the end of the hooked section, slide the locking tab down. Push the blade into the wiper arm through the connector. The grooved portion of the connector will go inside the hooked section of the wiper arm. Take the wiper blade and see where the grooves are. Secure the windshield with a towel so that it doesn’t crack if the wiper arm accidentally falls down. Step 3: Attach The Wiper Blade To The Wiper ArmĪgain, don’t forget to keep the wiper arm raised after you remove the old wiper blade. That means the connector is now locked into the wiper blade. You should immediately hear a clicking sound. Place the connector on top of the bracket mount and push it down. Hold the blade firmly in one hand and grab the connector with the other. You have to remove it before installing the blade on the I&L arm of your vehicle. The wiper blade will have a stock connector. Michelin Wiper Blades How To Install Rain X Wiper Blades On I&L Wiper Arms Step 1: Remove The Connector From The Blade Slowly lower the arm into the windshield. After the blade locks into the wiper arm, pull it and ensure it is firmly attached to the arm. Run the wiper blade into the J-hook and pull upward to secure its position. Take the wiper blade and insert the top part of the wiper arm’s J-hook through the opening of the wiper blade. Place a towel underneath so that it doesn’t suddenly fall, and smash your windshield. Step 3: Attach The Wiper Blade To The Wiper ArmĪfter you remove the old wiper blade, leave the wiper arm raised. The new adapter is now set with the Weatherbeater blades, and they are ready for installation. Firmly push the adapter into the wiper blade bracket, and you will hear a clicking sound. Place the adapter’s center channel on top of the cross pin of the wiper blade. That side will go towards the smallest hole on the wiper blade. How should you position the wiper blade? You will see that the adapter has a tab on one end. Next, you will have to take the new adapter out of the package and install it to the Rain X wiper blade. Grab the wiper blade frame with one hand and push the adapter up with the other. To begin, you will have to take off the pre-installed adapter on the Rain X wiper blade. How To Install Rain X Wiper Blades On J Hook Wiper Arms? Step 1: Remove The Pre-Installed Adapter Step 2 Connect The Blade To The Wiper Arm.Step 1 Remove The Pre-installed Connector.How To Install Rain X Wiper Blades On Narrow Pinch Tab Button Arms.Step 3 Connect The Wiper Blade To The Wiper Arm.How To Install Rain X Wiper Blades On Pinch Tab Button Arms?.How To Install Rain X Wiper Blades On Large Pin Wiper Arms?. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |